| John Deere |
212 JD Headers |
|
Many headers to choose from in various conditions. $4500 and down. |
| Call for details |
|
|
| 8820-15 |
214 JD Header w/ 7' Pickup |
|
Overall good condition, paint is faded, auger is good, typical throat wear. |
| Call for details |
|
$7250 |
| 8820-16 |
214 JD Header w/ 7' Pickup |
|
Straight w/ new floor, 4 nice belts and 3 good belts with tooth wear. |
| Call for details |
|
$8750 |
| 8820-14 |
912 JD Header w/ 6 Belt Pickup |
|
1.25" shaft, belts are very nice, no rear floor wear, auger has dents removed, runs true, clip on and go! |
| Call for details |
|
$6500 |
| 9760-1 |
914 JD Header w/o Pickup (Rebuilt) |
|
Rear upper arm repaired, very low acres, fits 7720-9610 early series (not a "P"), but can be converted, mint! |
| Call for details |
|
$7500 |
| 1680-8 |
1015 IH w/ 810 6 Belt Pickup |
|
Floor is fine, some larger auger dents, has slight wobble but will work fine as is. Has 6 belt 210 IHC pickup in decent condition with good belts. Clip on and use as is! |
| Call for details |
|
$4500 |
| 1660-3 |
1015 IH w/ 12' Rake-Up |
|
Some cosmetic dents in auger. Floor is fine, paint is not bad, quite nice overall. |
| Call for details |
|
$6500 |
| 1680-9 |
1015 IH w/ Super 8 Pickup |
|
Nice shape, auger is nice. Belts are bolted type for front and rear. They do have some weathering, but are decent as is. Teeth have been replaced recently with double teeth. Paint is quite nice. |
| Call for details |
|
$9000 |
| 1688-2 |
1015 IH w/ 7 Belt 388 Melroe |
|
This header is in very nice condition. Rubber belts and plastic teeth on the pickup. Belts look very nice. |
| Call for details |
|
$6500 |
| 2388-5 |
2015 IH w/ 14' Swathmaster |
|
New table auger and fingers as needed, new center floor panel, all new belts and paint. |
| Call for details |
|
$14900 |
| 2388-6 |
2015 IH w/ 14' Swathmaster |
|
New table auger and fingers as needed, new center floor panel, all new belts and paint. |
| Call for details |
|
$14900 |
| CIH |
525 CIH Hay Header |
|
Good condition, some dents in batts. |
| Call for details |
|
$5500 |
| 2388-6 |
1020 IH 30' Flex Header w/ Pickup Reel |
|
Hydraulic fore/aft, header height control. Pickup reel has steel teeth. It has a nice course knife. New front floor section. We have gone through this header and it is ready to clip on and use. |
| Call for details |
|
$15900 |
| 2388-5 |
1020 IH 30' Flex Header w/ Pickup Reel |
|
Hydraulic fore/aft, header height control. Pickup reel has steel teeth. It has a nice course knife. New front floor section. We have gone through this header and it is ready to clip on and use. |
| Call for details |
|
$15900 |
| 9600-7 |
930 JD 30' Straightcut w/ Batt Reel |
|
Fore and aft, auger has some cosmetic dents towards outer end of auger, but nice in the center. Runs true. Knife is near new, Batts do have some dents but are good as they are. 2 new center front floor sections. |
| Call for details |
|
$8500 |
| TR85-20 |
970 NH 18' Straightcut w/ Batt Reel |
|
2 seasons on fresh paint, very nice condition. We have many other options for 970 headers if this one isn't the one for you! |
| Call for details |
|
$6500 |
| TR96-8 |
971 NH 30' Rigid w/ Pickup Reel |
|
Reel was used one season. Table auger has some minor cosmetic dents but runs true. Missing RH and LH end shields. 2 new knives installed and 90% of p/u reel fingers replaced. We have many other options for 971 headers if this one idn't for you! |
| Call for details |
|
$9500 |
| 860-27 |
9024 MF 24' w/ Batt Reel |
|
Overall decent condition, paint is faded. Reel has some patches on batts, riveted knife in 85-90%, guards are good. Auger is straight. Does have nylon floor cover installed, but is weathered from sitting outside. |
| Call for details |
|
$3500 |
| 860-26 |
9030 MF 30' w/ Batt Reel |
|
No hydraulic kit, low hours, faded but nice. |
| Call for details |
|
$4500 |
| RB09 |
300 Series 27' Straightcut w/ Batt Reel |
|
Very Straight, fits N-R model Gleaners. |
| Call for details |
|
$4500 |
| L2-13 |
AC GLM Series 20' Straightcut w/ Pickup Reel |
|
Some auger dents. Usable as is. Fits M-L3 Gleaners. |
| Call for details |
|
$2750 |
| 116-2 |
9550 Claas 20' Flex Header w/ Pickup Reel |
|
This is a flex header with a pickup reel with steel teeth. Has crop lifters, knife is in decent usable condition with some wear. The header is in nice condition overall. It is Claas green with a red reel. Paint is okay but not mint. Floor and table auger are in very nice condition. |
| Call for details |
|
$4500 |
| 108-3 |
9550 Claas 25' Straightcut w/ Pickup Reel |
|
Has large auger. One cosmetic dent in floor from a stone. Skid plates are very beat up but otherwise the header is quite nice. The center skid plate is bent up far enough that it has bowed the floor up but it doesn't contact the auger. Plates are easy to remove and straighten. Could use some new pieces, such as fingers, knife guards, teeth, but can be used as is. |
| Call for details |
|
$7500 |
|